Tear test of Fabric by trapezoid method to ASTM D ASTM D covers the measurement of the tearing strength of textile fabrics by the trapezoid tear test using a constant-rate-of-extension-type (CRE) tensile. ASTM D Tearing Strength of Fabric by. Trapezoid Procedure. • Scope – this test method describes the determination of the tearing strength of fabrics by the.
| Author: | Guzilkree Dujar |
| Country: | Sudan |
| Language: | English (Spanish) |
| Genre: | Education |
| Published (Last): | 1 January 2017 |
| Pages: | 198 |
| PDF File Size: | 5.80 Mb |
| ePub File Size: | 5.97 Mb |
| ISBN: | 741-4-75976-944-9 |
| Downloads: | 51934 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Gulkis |
The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Wherever possible, this shall be prevented.
The reported value obtained is not directly related to the force required to initiate or start a tear. The reported value obtained is not directly related to the force required to initiate or start a tear. If a bias is found, either its cause must be found and corrected, or the x5587 and the supplier must agree to interpret future test results with consideration to the known bias. Users of previous versions of software such as Bluehill 2 and Bluehill 3 can d55887 upgrade to the newest version of Bluehill.
The method specifies a procedure to determine the tear force of textile fabrics using the trapezoid method. It is recognized that some constant-rate-of-traverse-type CRT tensile testing machines continue to be used.
ASTM D5587 Tearing Strength of Fabrics by Trapezoid Procedure
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The tearing force may increase to a simple maximum value or may show several maxima and minima, as shown in Fig.
Sampling and Test Specimens 7. Email addresses must contain the symbol. NOTE 2—The tabulated values of the critical asmt should be considered to be a general statement, particularly with respect to betweenlaboratory precision. The values stated in inch-pound units may be approximate. How can we help you?
ASTM D – 05 Standard Test Method for Tearing Strength of Fabrics by Trapezoid Procedure
Perform the test within 2 min after removal of the specimen from the water. The three woven fabric types were: Instructions are provided for testing specimens with or without wetting. Consequently, these test instruments may be used when agreed upon between the purchaser and the supplier.
It is useful for estimating the relative tear resistance of different fabrics or different directions in the same fabric. The components of variance for trapezoid tear strength expressed as standard deviations were calculated to be the values listed in Table 3.
Summary of Test Method 4. The conditions for use of the CRT-type tensile tester are included in. Consequently, these two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier.
As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. By means of our testing expertise and modular product design, we will help find the solution that is right for you. Forces up to 10 kN 2, lbf Low force tabletop systems Modular series of five frame options with adjustable test space Affordable testing option for tension, compression, bend, peel and much more.
At the same time, the force developed is recorded. Competent statistical assistance is recommended for the investigation of bias.
In any event, the CRE-type machine shall prevail. It is recognized ashm some constant-rate-of-traversetype CRT tensile testing machines continue to be used. A rectangular specimen is marked and prepared so that it can be loaded in the grip faces at an angle, allowing a tear to propagate across the specimen. When specimens are to be tested wet, take the specimens from areas adjacent to the dry test specimens.
Preparation of Test Apparatus and Calibration 8.
ASTM D – tearing strength of fabrics by the trapezoid procedure
Onsite Training At Your Facility. The challenges of testing to this standard are: This precaution is most important when testing bowed fabrics. The values stated in inch-pound units may be approximate. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
Tear Strength of Fabrics – Trapezoid Procedure
Strong fabrics or fabrics made from glass bers require special adaptation to prevent them d55887 slipping in the clamps or being damaged as a result of being gripped in the clamps. Consequently, these two tensile testers cannot be used interchangeably unless the degree of quantitative correlation has been established between the purchaser and the supplier.
Email addresses can only contain letters, numbers and the following special characters: In any event, it is recommended that computer-processed data be veried against known property values and its software described in the report. Describe the fabric or product sampled and the atsm of sampling used. Instructions are provided for testing specimens with or without wetting.
Link to Active This link will always route to the current Active d55877 of the standard.
